Since I’ve built a ton of J-Poles and wire Antennas, I’ve wanted to build something different. I decided on a 3 element YAGI built for GMRS that is directly fed with 50ohm coax. After a couple of failed yagis and the help of another ham on QRZ.com forums, I finally built a Yagi that works! The reason I’ve chosen a Yagi built for GMRS is due to the ultra high frequency, which ends up being a small antenna. If I were to mess up (Which I did), the material cost would be low. I also wanted to use it on a GMRS repeater in the area.
The first Design I used is with a Web Site that has a Java base applet to design the Yagi, After getting all the Dimensions from the website, I went to work building the antenna. After everything was done, I learned two things. One is that my drill press does not drill straight (90 Degrees) through the tubing. The other thing is that when I hooked up the antenna to a simple SWR Meter, That didn’t work either (Pegged the Meter). At this point I got frustrated and posted my issue on QRZ.com. A Ham by the call of WB3BEL (Harry) took my dimensions (That I got from the applet) and plotted my antenna into 4NEC2 software (Like EZNEC but freeware) and it would not work for the center frequency of the GMRS Band (or any part of the GMRS band).
WB3BEL actually re-designed the antenna to where it would work so I give him credit and major thanks for help. I took his Dimensions, Modeled the antenna for fabrication and built the antenna. I Hooked up the antenna to a transceiver and SWR meter and got a 1.2:1 SWR and a 1.5:1 SWR on the outsides of the GMRS band. The Design is calculated to yield 7.5Dbi of Gain. Considering connector and cable loss (Lets say 4Dbi using 50ft RG-213 W/ 3 SO-259 Ends and a Barrel Connector) still yields gain of around 3.5Dbi which is not too bad.
Here is rendered Image of the Antenna. The elements are Insulated from the boom using plastic shoulder washers for the Reflector and director. The Driven Element is insulated using a 0.750(OD)X.375(ID)X1.5″(L) Plastic spacer. Since the elements are going THROUGH the boom, It will make the elements electrically shorter so you have to compensate for the loss by adding 0.279528″ (7.1mm) to the element to correct the effect (Boom correction). The elements are secured using #8-32 Screws screwed to the boom. The screws are also insulated from touching the boom. The screws do not make any significant changes to radiation pattern of the antenna as long as it’s insulated from (not touching) the boom. I did notice that the screws actually lowered the SWR a tad which is great.
I didn’t add a matching network to the antenna because I wanted an easy to build and assemble antenna which is the entire point of this article. The antenna is fed using RG-213 Coax with terminals soldered to the core and shield. I tried to keep everything as short as possible because this and the ring terminals effect the performance and SWR of the antenna.
Here are a couple of screen shots from the antenna software that show the Radiation Pattern and gain. Nothing special here.
Here is the calculated results for the SWR of this Yagi. Please note that it’s in the ball park. By adding screws, coax leads and the ring terminals, it could or will effect the final pattern and/or performance of the antenna.
Here is a SWR Shot. As you can see, I don’t have a very good meter. I would like to buy a HF/VHF/UHF Antenna analyzer for my Antenna builds but I don’t think that will happen in the near future.
Here is the complete Antenna.
Overall it was a fun little project. It took a short time to build and it’s a great directional antenna with some gain to help your signal on GMRS reach its destination.
Continue reading if you want to build this antenna.